Slide

  • LINUX

    LINUX:In 1969 AT&T made a decision to withdraw Multics and go with GECOS (General Electric Comprehensive Operating Supervisor / System), with AT & T in Bells Lab when Multics was withdrawn some of the programmers named Ken Thompson and Dennis Ritchie decided to rewrite operating system in order to support low cost computer..To Know More

    CLICK HERE

  • MICROSOFT

    MICROSOFT:Microsoft was established to develop and sell BASIC interpreters for the Altair 8800. It rose to dominate the home computer operating system market with MS-DOS in the mid-1980s,followed by the Microsoft Windows line of operating systems. To Know More

    CLICK HERE

  • CISCO

    CISCO:During the early 1980s, there was a married couple namely Len and Sandy Bosack who used to work in two different departments of computer located in Stanford University. This couple was facing problem in making their computers communicate with each other To Know More

    CLICK HERE

showinfo=1

configuring frame relay switch in gns3

FRM Router which is in middle working as a frame-relay switch


Frame-relay Switch Configuration Commands

FRS#configure terminal

FRS(config)#frame-relay switching

FRS(config)#interface serial 1/0



FRS(config-if)#encapsulation frame-relay

FRS(config-if)#frame-relay intf-type dce

FRS(config-if)#frame-relay route 204 interface serial 1/1 402

FRS(config-if)#frame-relay route 203 interface serial 1/2 302

FRS(config-if)#no shutdown

FRS(config-if)#exit

FRS(config)#interface serial 1/2

FRS(config-if)#encapsulation frame-relay

FRS(config-if)#frame-relay intf-type dce

FRS(config-if)#frame-relay route 302 interface serial 1/0 203

FRS(config-if)#frame-relay route 304 interface serial 1/1 403

FRS(config-if)#no shutdown

FRS(config-if)#exit

FRS(config)#interface serial 1/1

FRS(config-if)#encapsulation frame-relay

FRS(config-if)#frame-relay intf-type dce

FRS(config-if)#frame-relay route 402 interface serial 1/0 204

FRS(config-if)#frame-relay route 403 interface serial 1/2 304

FRS(config-if)#no shutdown

FRS(config-if)#exit

FRS(config)#


R2 Configuration Commands

R2#configure terminal

R2(config)#interface serial 1/0

R2(config-if)#encapsulation frame-relay

R2(config-if)#no shutdown

R2(config-if)#interface serial 1/0.1 point-to-point

R2(config-subif)#frame-relay interface-dlci 203

R2(config-fr-dlci)#ip address 192.168.2.1 255.255.255.252

R2(config-subif)#interface serial 1/0.2 point-to-point

R2(config-subif)#frame-relay interface-dlci 204

R2(config-fr-dlci)#ip address 192.168.1.1 255.255.255.252

R2(config-subif)#end

R2#


R3 Configuration Commands

R3#configure terminal

R3(config)#interface serial 1/0

R3(config-if)#encapsulation frame-relay

R3(config-if)#no shutdown

R3(config-if)#interface serial 1/0.1 point-to-point

R3(config-subif)#frame-relay interface-dlci 302

R3(config-fr-dlci)#ip address 192.168.2.2 255.255.255.252

R3(config-subif)#interface serial 1/0.2 point-to-point

R3(config-subif)#frame-relay interface-dlci 304

R3(config-fr-dlci)#ip address 192.168.3.1 255.255.255.252

R3(config-subif)#end

R3#


R4 Configuration Commands

R4#configure terminal

R4(config)#interface serial 1/0

R4(config-if)#encapsulation frame-relay

R4(config-if)#no shutdown

R4(config-if)#interface serial 1/0.1 point-to-point

R4(config-subif)#frame-relay interface-dlci 402

R4(config-fr-dlci)#ip address 192.168.1.2 255.255.255.252

R4(config-subif)#interface serial 1/0.2 point-to-point

R4(config-subif)#frame-relay interface-dlci 403

R4(config-fr-dlci)#ip address 192.168.3.2 255.255.255.252

R4(config-subif)#end

R4#
After configuring everything start checking whether you can ping both site from each router.
you should get the output like this..

R2#ping 192.168.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 96/136/164 ms

R2#ping 192.168.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 128/142/160 ms
----------------------------------------------------------------------------------------------------

R3#ping 192.168.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/128/164 ms

R3#ping 192.168.3.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.3.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 132/175/208 ms
-------------------------------------------------------------------------------------------------------

R4#ping 192.168.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 100/144/196 ms

R4#ping 192.168.3.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.3.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 128/148/188 ms
---------------------------------------------------------------------------------------------------------


16 comments:

  1. Fantastic post however I was wanting to know if you could write a litte more on this subject? I'd be very thankful if you could elaborate a little bit more. Cheers!
    jarrowpomhealth.com |

    ReplyDelete
  2. You have done a great job. I will definitely dig it and personally recommend to my friends. I am confident they will be benefited from this site .
    www.consciousbusinesspromotions.com |

    ReplyDelete
  3. Thanks so much with this fantastic new web site. I’m very fired up to show it to anyone. It makes me so satisfied your vast understanding and wisdom have a new channel for trying into the world.
    southtyroltravels |

    ReplyDelete
  4. well, this is an amazing thing that I found here. You tried best to achieve your thoughts. 
    njhomebrewsupply.com |

    ReplyDelete
  5. All the contents you mentioned in post is too good and can be very useful. I will keep it in mind, thanks for sharing the information keep updating, looking forward for more posts.Thanks
    autonomyla.com |

    ReplyDelete
  6. Mate this is a very nice blog here. I wanted to comment & say that I enjoyed reading your posts & they are all very well written out. You make blogging look easy lol I’ll attemp to start a blog later today and I hope it’s half as good as your blog! Much success to you!
    lafrancaistruck |

    ReplyDelete
  7. This web site is really a walk-through for all of the info you wanted about this and didn’t know who to ask. Glimpse here, and you’ll definitely discover it….
    kre8ivelance.com |

    ReplyDelete
  8. This article gives the light in which we can observe the reality. This is very nice one and gives indepth information. Thanks for this nice article.
    marchofdimesillinois |

    ReplyDelete
  9. Great article Lot's of information to Read...Great Man Keep Posting and update to People..Thanks 
    freeinvestmentcourse |

    ReplyDelete
  10. This is a smart blog. I mean it. You have so much knowledge about this issue, and so much passion 
    Home base Club |

    ReplyDelete
  11.  It is very helpful for all the people on the web.I wanted to say that it's nice to know that someone else also mentioned this as I had trouble finding the same info elsewhere.
    Black and Blanco Food |

    ReplyDelete
  12. This comment has been removed by the author.

    ReplyDelete

  13. نقل عفش داخل جدة نقل عفش داخل جدة
    دينا نقل عفش جدة دينا نقل عفش جدة
    افضل شركة نقل عفش من جدة الى الرياض افضل شركة نقل عفش من جدة الى الرياض

    ReplyDelete

Note:- Comment as: Option available to post without login select "Anonymous" from the drop down...........

For Latest Updates: Subscribe Now | | Test Your Knowledge, Take a Quiz now Click Here | | Site Best Viewed In Firefox

X